fita commercial sports car

(upbeat music) - hi, i'm chris, and today, we're goingto be putting together the dynacraft hello kittysix-volt sports car. after about thirty-fiveminutes of assembly and a full charge, it'll be ready to ride! assembly of the hello kitty sports car should only be done by an adult, and children should not be allowed

to handle small parts ofthe unassembled ride-on. before we begin, you'll need a philips-head screwdriverand a pair of pliers from your tool chest. two seventeen-millimeter socket wrenches are included with the vehicle. scissors or a box cutter are useful for cutting packaging. you will also need two double-a batteries

for the steering wheel. open the box and checkthat all parts are present. you can check against thelist in the assembly manual. if any parts are missing or damaged, or if you have anytrouble with the assembly, don't return to the store. call dynacraft at one, eight hundred, two eighteight, one five six zero. we strongly recommend reading the manual

or watching this video all the way through before you begin the assembly, and you should read theentire owner’s manual supplied with the sports car before letting anyone ride it. this video is not asubstitute for the manual, which contains very important information for the safe use of thehello kitty sports car. okay, let's get this ride-on assembled!

first, we're going to workon the front wheel assembly. for each side, you'll needtwo number twelve washers, a bushing, an m-ten locknut, an axle cap, and the wheel, of course. this hardware may alreadybe installed on the axle. begin by turning thevehicle body upside down. start on one side. remove any hardware that isalready installed on the axle. now, slide one number-twelvewasher onto the axle,

followed by a bushing. the tabs on the bushing should be facing the washer we just installed. next, place the wheel on the axle, matching the inside to thebushing you just installed. slide the second washer onto the axle, and add the locknut. tighten the nut with your fingers, then finish tightening withthe included socket wrench.

be careful not to over-tighten the nut. stop when the threads start to show on the outside of the nut. spin the wheel. if it doesn’t spin freely, loosen the nut a quarter turn and test it again. now repeat these steps for the other side. next, we're going to installthe rear axle and wheels. for the right-side drive wheel,

you'll need the gear box, one number-twelve washer, an m-ten locknut, an axle cap, and the wheel. remove all hardware from the axle. notice that one side islonger than the other. remember, we are installingthe right-side wheel, but we’ll start by sliding the longer side of the axle through theleft side of the car.

slide the washer onto the long side of the axle before installing it. after putting it in place,move to the right rear wheel. slide the gear box throughthe axle and into the body. as it moves into place, be sure the motor and power wire are inserted into the hole in the car's body. next, install the driving wheel, matching it up with the gear box.

install the washer,followed by the locknut. you may need to hold theaxle with a pair of pliers to prevent it from turning. tighten the locknutuntil the threads begin you're done here! the left-side rear wheel isn't powered, so installing it is thesame as the front wheels, although you will need to use both included socketwrenches to tighten it.

after you have tightened the left wheel, remember to check to makesure that it spins freely. if it doesn’t, just loosen the nut a quarter turn at a time until it does. now that we've installed all four wheels, we need to check to make sure they have the correct gap. if there is a large gap between the outside of the wheel

and the screw thread, you need to pull the wheel off and add one number-twelve washer to the inside of the wheel. reinstall and re-tighten the wheel. again, be careful not toover-tighten the locknut. give a little spin to make sure the wheel moves smoothly and without wobbling. if there is any resistance,

or if the nut is pressingagainst the wheel, remove one or two washers. repeat this check for all four. after that, install the axle caps on all four wheels, making sure to line up the tabs on the cap with the inside of the wheel beforeclicking them into place. now, we're going to installthe steering column. we need two number-ten washers,

a split pin, and the column. turn the car on its side and find the correct holeunderneath the front. place a washer over the straight end of the steering column, then slide the column through the hole until it's sticking out of the top. next, install the bent end into the correct holeon the front axle, here.

place a washer over it, and insert the split pinto hold the axle in place. use your pliers to open the pin ends. let's move on to the steering wheel. turn the vehicle back upright. there is already a machine screw and nut installed in the steering wheel. remove them and set them aside. slide the steering wheelover the steering column,

making sure you line up the two holes. now, slide the screwback through the hole, then reinstall the nut,tightening with your screwdriver. then, use the screwdriver toopen the battery compartment, and insert two double-as. to mount the windshield, fit the tabs into the slots, andgive a firm, steady push with both hands untilit clicks into place. it's time to connect the battery.

it's already installed, but the power connectionsare not hooked up. simply plug the two whiteconnectors together. do the same for red connectors. this piece is called a motorhood. use four four-by-twelve flat-head screws to install it here,below the seating area. make sure the wirescome out of these slots. to attach the seat, startby moving the seat belts

out of the way. insert the tabs at the back of the seat into the matching slotsin the vehicle body. fasten the bottom of the seat into place with two m five-by-sixteen machine screws. your hello kitty sportscar comes with an mp3 port, and the included cable plugsinto the dashboard, here. mp3 devices are not included. now all that's left to dois power up the battery!

the input socket is right here. make sure you only use the charger that came with the vehicle. it's very important to always let the battery charge all the way. check the led, and once it's green, your little girl can start exploring! please refer to the manual for specific operations andappropriate environments,

and make sure the rider takes it easy while she is getting afeel for the sports car. and we're done putting together remember, if you haveany questions or problems during assembly, justgive dynacraft a call. now, it's time to takethis baby out for a spin! this video is forinformational purposes only and does not replace the owner’s manual supplied with the product.

please read the owner’s manual for complete assembly instructions and important safety information. and remember, be safe.